Classpad II fx-CP400 hardware - a hidden SD card reader ?

critor

In a previous TI-Planet news, Adriweb published a software test of the Casio ClassPad II fx-CP400 sample he received from TSPromotion.


Today let's discover its hardware together.

The calculator is quite easy to open once you get the trick. After removing all 6 screws on the back (including 4 inside the battery compartement), the entire front plate (screen and keyboard included) must be detached from the case by forcing on one of the corners :)




And now, you get the ClassPad II fx-CP400 hardware:


The hardware consists of two distinct PCBs :

• the power supply board RJA527047-001V01 (LY777-E4W)
• the motherboard RJA527046-001V02 (LY777-1)

It seems that is the second version of the motherboard, but of the first version of the power supply board.
We can take that with two distinct boards, a future version powered by a rechargeable battery would be quite easy, and the system already supports it.




The motherboard seems to have a setup close to the ones found on most recent Casio graphic calculators USB (Casio fx-9750Gii/fx-9860Gii, Casio Prizm fx-CG10/20).

It's built around 3 integrated chipsets:

• at position U101, a processor chip on which we can't get more information for now, as it's been drowned in a solid epoxy drop (which is usual with Casio)
• at position U231, a huge SDRAM memory chip - M12L128168A from ESMT - 2Mbits x 16-bits x 4 banks, which results in a 2 MB RAM
• at position U221, a NAND Flash memory chip - S99 50338 from Spansion - however its datasheet is not public

About the RAM, the RAM chip was also 2MB on the Casio Prizm, but only 64KB were available for the user. And here in a similar way, we've only got 512 KB available for the user! :(


About the NAND Flash ROM, if the informations found on the official website are accurate, the chip should have a capacity of 32MB, but only 5.5MB would remain available for the end user.



About the connectivity, a huge surprise awaits us. We've got:

• at positions HS401 et CN501, the connections to the power supply board
• at position CN401, the mini-Jack connector to transfer data between calcuators
• at position CN102, the mini-USB connector for a computer
• at position CN703, an unsoldered connector! :o

This CN703 connector with its pinout of 9 contacts and one lateral contact, and by its shape that gives an empty space on the board is clearly a connector for an SD memory card reader! :D
Unlike older Casio Classpad models, it is possible to add a SD card memory reader to the ClassPad II!




We're not sure if Casio has a future project for this since it would be a forbidden module by exam regulations of some countries (including France).
Traces of SD memory card reader support were already found on TI-Nspire and even on Casio Prizm fx-CG10/20 operating systems, although they were clearly missing from the hardware.
In fact, it seems those readers are used during hardware development where they give a way to reprogram or emulate easily the content of the ROM memory during tests - and so avoid permanently bricking the calculator prototypes with bad code: you just need to switch the SD card.

However, the community could clearly wonder if there wouldn't be some possibility for us to add a working SD card reader ourselves ;)



Source:
http://tiplanet.org/forum/viewtopic.php?t=12716&lang=en

零下一度

硬件好低端的感觉

wtof1996

Impressive discovery.

imath

按CASIO的风格，估计很快要出Classpad 400 SD了

We should balance the advantage and disadvantage of adding SD card reader.
The SD card can memorize lots of things. But it can cost a lot of power to run it.
Sorry for my bad English.

月与映之皮丘

SD Card...Can it support SD Card well?
fx-9860 Series can't support SD card well...

lch

I wonder whether its OS has the module to read and write SD card.

yzskyt

匿名者 发表于 2013-7-24 12:36
We should balance the advantage and disadvantage of adding SD card reader.
The SD card can memorize ...

memorize？你当SD卡是人啊

yzskyt 发表于 2013-7-24 15:18
memorize？你当SD卡是人啊

我们老师说可以.....

晓零辛纳

im looking forward classpad 400 SD(classpad II SD)

abcaf

deleted

helder7

lichensheng121 发表于 2013-7-24 16:35
I've ever found that there is a similar connector for SD card on fx-9860G slim and someone has conne ...

Using custom add-ins is not possible? I wrote an exemple of add-in that wrote a txt file to sd card, here is the source:


int AddIn_main(int isAppli, unsigned short OptionNum)
{
    unsigned int key;
        char buffer[8] = {'C','A','S','I','O','-','S','D'};

FONTCHARACTER PathName[55] = {'\\', '\\', 'c', 'r', 'd', '0', '\\', 'F', 'X', 'S', 'L', 'I', 'M', '.', 't', 'x', 't', 0};
int aa;

Bdisp_AllClr_DDVRAM();

  Bfile_DeleteFile(PathName);
  Bfile_CreateFile(PathName, 3000);
  aa = Bfile_OpenFile(PathName, _OPENMODE_WRITE);
  if (aa < 0){
    //Error
                locate(1,1);
    Print((unsigned char*)"Error!");
    Bfile_CloseFile(aa);
  }
  if (aa >= 0){
                locate(1,1);
    Print((unsigned char*)"File created!");
    Bfile_WriteFile(aa, buffer, sizeof(buffer));
    Bfile_CloseFile(aa);
  }


    while(1){
        GetKey(&key);
    }

    return 1;
}

would be nice if someone with a modded fx9860g slim like this http://www.cncalc.org/thread-2376-1-1.html test it.

lenovotcldellhp

卡西欧啥时候能出个没牛屎的计算器啊

qingfengx12

期待日后改善